Readers are advised to proceed with the construction of the presented circuits only after understanding the concepts from the core. Not adhering to this can lead to failures and frustrations.

Search This Blog

Loading...

Thursday, December 8, 2011

How to Make a 50 Watt Small Homemade Inverter – A school Science Exhibition project

A 50 watt inverter might look quite trivial, but it can serve some useful purposes to you. When outdoors, this small power house can be used for operating small electronic gadgets, soldering iron, table top radios, incandescent lights, fans etc.


Let’s learn how to build this homemade 50 watt inverter unit, beginning with a brief description regarding the circuit diagram and its functioning:

Circuit Description

The circuit may be understood with the following points:
Referring to the figure, transistors T1 and T2 along with the other R1, R2, R3 R4, C1 and C2 together form a simple astable multivibrator (AMV) circuit. A multivibrator circuit basically is composed of two symmetrical half stages, here its formed by the left and the right hand side transistor stages which conduct in tandem or in simple words the left and the right stages conduct alternately in a kind of a perpetual “motion”, generating a continuous flip flop action.
The above action is responsible of creating the required oscillations for our inverter circuit. The frequency of the oscillation is directly proportional to the values of the capacitors or/and the resistors at the base of each transistor.
Lowering the values of the capacitors increases the frequency while increasing the values of the resistors decreases the frequency and vice versa. Here the values are chosen so as to produce a stable frequency of 50 Hz.
Readers, who wish to alter the frequency to 60 Hz, may easily do it by just changing the capacitor values appropriately.
Transistors T2 and T3 are placed at the two output arms of the AMV circuit. These are high gain; high current Darlington paired transistors, used as the output devices for the present configuration.
The frequency from the AMV is fed to the base of T2 and T3 alternately which in turn switch the transformer secondary winding, dumping the entire battery power in the transformer winding.
This results in a fast magnetic induction switching across the transformer windings, resulting the required the mains voltage at the output of the transformer.



Parts Required


You will require the following components for making this 50 watt homemade inverter circuit:
R1, R2 = 100K,
R3, R4 = 330 Ohms,
R5, R6 = 470 Ohms, 2 Watt,
R7, R8 = 22 Ohms, 5 Watt
C1, C2 = 0.22 uF, Ceramic Disc,
D1, D2 = 1N5402 or 1N5408
T1, T2 = 8050,
T3, T4 = TIP127,
T5, T6 = 2N3055 (TO-220)
General purpose PCB = cut into the desired size, approximately 5 by 4 inches should suffice.
Battery: 12 volts, Current not less than 10 AH.
Transformer = 9 – 0 – 9 volts, 5 Amps, Output winding may be 220 V or 120 volts as per your country specifications
Sundries: Metallic box, fuse holder, connecting cords, sockets etc

Testing and Setting Up the Circuit

After you finish making the above explained inverter circuit, you may do the testing of the unit in the following manner:
Initially do not connect the transformer or battery to the circuit.
Using a small DC power supply power the circuit.
If everything is done rightly, the circuit should start oscillating at the rated frequency of 50 Hz.
You can check this by connecting the prods of a frequency meter across T3’s or T4’s collector and the ground. The positive of the prod should go to the collector of the transistor.
If you don’t own a frequency meter, never mind, you do a rough checking by connecting a headphone pin across the above explained terminals of the circuit. If you hear a loud humming sound, will prove that your circuit is generating the required frequency output.
Now it’s time to integrate the battery and the transformer to the above circuit.
Connect everything as shown in the figure.
Connect a 40 watt incandescent lamp  at the output of the transformer. And switch ON the battery to the circuit.

The bulb will immediately come ON brightly…..your homemade 50 watt inverrer is ready and may be used as desired by for powering many small appliances whenever required.

208 comments:

  1. what are D1 and D2?

    ReplyDelete
    Replies
    1. Hi sir can i connect this 50watt inverter connection on bread board or should i use only pcb.Also if 5 amp transformer is taken is there still any chance of transistor heating.
      can i get the reply to sarath_swades@yahoo.com

      Delete
    2. Hi Sarath,

      You may try it over a breadboard for trial.

      Transistor will heat up with 5amp transformer and a 12V 7.5AH battery, so use very good(large) heatsink for the transistors

      Delete
    3. what are R1, R2 ,R3 ,R4, C1, C2, D1, D2, T1, T2, T3, T4

      Delete
    4. Resistors, Capacitors, Diodes, and Transistors respectively.

      Delete
    5. Hi sir,
      can i use 500mA transformer in this circuit? i couldnt get 5 Amp transforemr in the market?

      Delete
    6. No, 500mA will not produce any power, at least 3 amps is a must....

      Delete
    7. Hi Sir,
      The said transformer 5Amp is very large for the PCB and also not available 9-0-9 in Berhampur, Ganjam,Odisha and also the transistor TIP127(TIP127,126&125) not available because, it produces more heat in few seconds. So can I use any other transistor ? Please reply the alter transistor name.....

      Delete
    8. Hi Ramchandra,
      5amp is not large, it will only produce 50wats, you can use smaller tranformer with much lower outputs.

      you can try the following design if the above circuit parts are difficult to find in your area:

      http://homemadecircuitsandschematics.blogspot.in/2012/02/how-to-make-simplest-inverter-circuit.html

      Delete
    9. Hi, Sir
      The all parts said
      R1, R2 = 100K,
      R3, R4 = 330 Ohms,
      R5, R6 = 470 Ohms, 2 Watt,
      R7, R8 = 22 Ohms, 5 Watt
      C1, C2 = 0.22 uF, Ceramic Disc,
      D1, D2 = 1N5402 or 1N5408
      T1, T2 = 8050,
      T5, T6 = 2N3055 (TO-220)
      Are already buy, but The T3, T4= TIP127 is not available, can I Use Transistor no: ZTX749A or 2STR1215 or STN851 or other in this circuit.Please clear my confusion....

      Delete
    10. Hi Ram,
      you can try BD680, any other will not give proper results

      Delete
    11. Hi Sir
      Can I use 12-012, 6Amp transformer in this ckt?....

      Delete
  2. Thanks for pointing out the mistake! D1 and D2 are 1N5402 diodes, I'll include them just now....

    Thanks.

    ReplyDelete
  3. hello sir.i want to know how a charging light works. in my home i have a charging light consists of a 20 watts tube light. i want to make another charging light which can be used to light up a 15 watts floroscent lamp using battery of 6v,4ah obtained from the charging light.
    with regards.

    ReplyDelete
  4. Hi Harish
    Charging lights with fluorescent lamps are difficult to build because it requires complicated inductor transformers, instead you can go for LED emergency light which is very easy to build and gives more backup time.

    ReplyDelete
  5. thank you very much sir for your kind information.i want to know how a fluorescent lamp works.i got a fluorescent lamp which is broken. can i make any any interesting thing with that.

    ReplyDelete
  6. Hi Harish,

    Thanks, I have posted a florescent ballast circuit, you can search for it here and use it to power a 40 watt tube light, however the project is a bit difficult :-)
    Regards

    ReplyDelete
  7. how to design 1KW inverter, we have given 48v of battery, we have problem with output current

    ReplyDelete
    Replies
    1. Hi Mithilesh,
      I'll design the above circuit and let you know once it gets published, soon.

      Regards

      Delete
  8. The TIP127 transistors are getting too much heated after 10-20 seconds.Please tell me some tips or replacement tricks..to get out of this problem.Thanks in advance..

    ReplyDelete
    Replies
    1. Put them over large heatsinks or attach more transistors in parallel in the way shown below:

      http://homemadecircuitsandschematics.blogspot.in/2012/02/how-to-make-500-va-pwm-controlled.html

      Regards.

      Delete
  9. is rectifier circuit need for home made inverter?

    ReplyDelete
    Replies
    1. I Couldn't understand your question??

      Delete
    2. hi swagatam i have few doubt on inverter...that i given below..

      1.how to recharge the battery?

      2.rectifier circuit need for inverter?


      plz help me friends

      Delete
    3. Hi Ganesan,

      Yes, you will require a separate 12 volt transformer with a rectifier/capacitor circuit for recharging the battery.

      Regards.

      Delete
    4. hi swagatam , thanks for your valuable reply,


      i dono how to design 12 volt transformer with a rectifier/capacitor circuit..
      can you help me??
      shall you send some link about 12 volt transformer with a rectifier/capacitor circuit??

      i eagerly await swagatam...

      Delete
  10. hi Swagatam thanks for replaying,

    i don't know how to make 12 volt transformer with a rectifier/capacitor circuit for recharging the battery.
    can you teach me?
    if you have link about 12 volt transformer with a rectifier/capacitor circuit means share the links.
    i eagerly awaiting for your replay.

    ReplyDelete
    Replies
    1. Hi Ganesan,

      See the example circuit in the following link:

      http://homemadecircuitsandschematics.blogspot.in/2012/02/how-to-make-remote-control-circuit-from.html

      D1---D4 are arranged as bridge and C5 is the filter capacitor, all these are connected to the secondary winding of the shown transformer and the primary of the transformer is connected to the AC mains input.

      Regards.

      Delete
  11. hi Swagatam thanks for replaying,

    i don't know how to make 12 volt transformer with a rectifier/capacitor circuit for recharging the battery.
    can you teach me?
    if you have link about 12 volt transformer with a rectifier/capacitor circuit means share the links.
    i eagerly awaiting for your replay.

    ReplyDelete
  12. hi Swagatam thanks for clearing my doubt...

    i would like to make 300watts inverter.can you give ckt diagram & spec for me..

    thanks & regards
    ganesan

    ReplyDelete
    Replies
    1. Hi Ganesan,

      You can try the circuit shown in the following article:

      http://homemadecircuitsandschematics.blogspot.in/2012/02/how-to-make-simple-200-va-homemade.html

      Regards

      Delete
  13. 50 Watt Small Homemade Inverter
    i want the calculation of the total circuit componets..
    plz help me and send some mathematical calculations..

    thank u

    ReplyDelete
  14. 50 Watt Small Homemade Inverter
    iwant to know all the calculation of the components of this 50 watt inverter .
    plz send me the some mathematical calculations about this project..

    email id - litanparida1991@rediffmail.com

    thank u

    ReplyDelete
  15. TIP127 base resistance is calculated with the formula:

    R = (Ub - 0.6) × Hfe ÷ transformer input current.

    The frequency of the circuit is calculated using the formula:

    f = 1/1.38RC, where R1 = R2 = R and C1 = C2 = C

    Regards.

    ReplyDelete
  16. Swagatam,
    Can you tell me what quiescent current the inverter takes and the current
    under a full - say 40-45watt load.

    Regards

    Richard.

    ReplyDelete
    Replies
    1. Richard,

      The circuit has not been tested by me so cannot tell you the exact details.

      Regards.

      Delete
  17. Hlw sir,how long the inverter power will be survive when it is connected with 2 CFL light of 25W with car battery.I mean how much time did it glow for those CFL?plz mail me at my id nischal_raj2002@yahoo.com Coz m impressed with your designed n also want to try it thank you

    ReplyDelete
    Replies
    1. Hi

      Thanks, actually I did not test this circuit practically, but I assume that it would provide at least a 5 hours back time with the above load and inputs.

      Regards.

      Delete
  18. Being an electrical novice,I wanted the conversion using SCR(thyristors) as the main functioning element of the circuit..
    Is there any practical feasibility using any kind of power electronic elements

    Regards

    ReplyDelete
    Replies
    1. SCRs cannot oscillate with DC loads, so I think it is not a feasible idea to put SCRs in the above circuit.

      Delete
  19. hi sir as i ask u earlier about tv remote control jammer,is it work on dish set of box?
    nd can u give me the circuit of radio station of min frequency? i mean want to make at home

    ReplyDelete
    Replies
    1. Hi Rishabh,

      No, it will not work on set box, because they operate at different frequencies, very high....

      "radio station at min frequency", I didn't understand, can you elaborate??

      Delete
  20. hi sir,is can we use this inverter for a fan

    ReplyDelete
  21. sir please give me reply as soon as possible

    ReplyDelete
    Replies
    1. Yes you may use for powering a small table fan

      Delete
  22. sir how much money is needed to make it

    ReplyDelete
  23. This is a very nice project,I dohave 2 old 12 v 7 Ah SlA Batteries.Can i Connect these in Parralal Connection and use in the above circuit,Waiting For your reply,I amvery interested tobuild this

    ReplyDelete
    Replies
    1. Yes you can make the circuit and connect the batteries in parallel.

      Delete
  24. I have made the circuit in pcb with 12-012 v 600 ma.But the output is 220 volt but unable to light 8 w cfl.Can I Use 12-012 v 2amp Ct Transformer.for 120 V it is 50 watt for 220 volt how much watt it will be,
    Please give me a suggestion,if i only want to light cfl,then inverter is good or for every cfl "driver Circuit for CFL-12 v is good",I have accumulated 5 Old Sla Batteries from Solar Light and UPS ,Give me some Suggestion to Utilize These to light some cfls,
    One More thing,TIP 127 are getting extremely hot,Smoke is coming out,I have provided them with heat sink.Please guide me,Waiting eagerly
    I do have one old 600 Va transformer from my OLD UPS,Can I use IT

    ReplyDelete
    Replies
    1. 600mA transformer will not work, you will need at least a 5Amp transformer.
      I think a 12v driver circuit is better if you want to light only CFLs
      Use the transformer and battery as suggested in the article, other options would make the transistor hot and blow them.
      600VA is far too big, might not work properly.

      Delete
  25. I am very interested in your project,I have some old 7 Ah 12 V SLA batteries,I wnt to light 3 Cfl during load shedding,Please guide me,Should i use ready made 12 v cfl driver or above mentioned Inverter,

    Thanks
    Avisek

    ReplyDelete
    Replies
    1. OK then please make the following circuit:

      http://www.electroniccircuitsdesign.com/power-supplies-circuits/12-250v-converter-circuit-diagram-electronic-project.html

      It is a wonderful circuit.

      Delete
  26. And Also suggest a charger circuit for parallaly connected 4 to 6 old "12 v 7Aah" sla Batteries.
    I want to use the same transformer used in the inverter,
    "I am having a plan of connecting these batteries( parallaly connected 4 to 6 old "12 v 7Aah" sla Batteries) to my old 600 VA UPS,I have tried this also,and it can light 5watt cfl for almost 1 hour,and i will incorporate a charger for these batteries"
    Do you think this will be a good idea,
    Waiting for your reply.

    ReplyDelete
    Replies
    1. I have published many battery charger circuits, you may choose any one of them for your requirement.
      Yes you may charge them all with parallel connections.

      Delete
  27. Thanks in advance,
    With your help i have almost reused my old batteries,
    I have already made charger for my battery,This working great,
    http://homemadecircuitsandschematics.blogspot.in/2012/02/how-to-build-automatic-6-volt-12-volt.html
    Only problem is monitoring led,If connected create problem,I have used 3 amp Transformer for 4 Batteries,I am planning to do the parallal connection with diode ,so that weak battery does not steal any energy from strong ones,Is it ok,
    I have seen the "220 v converter circuit",for 3 cfl 3*8watt=18 watt,What transformer should i use with the circuit,
    Is 9-0-9 Volt 750 ma will do the job,I do have one with me,
    Or i can purchase ready made cfl ballast for 12 v DC,Guide me,
    Thanking You,
    Waiting for your precious reply
    Avisek Chakraborty

    ReplyDelete
    Replies
    1. 9-0-9v 750ma will not work, you will need at least a 5amp transformer.

      Delete
    2. Can i use 12-0-12 transformer 5A sir

      thanks

      reply ASAP pls...

      Delete
    3. hi sir thanks for the answer!! another question - im a 4th year high school student in the phils. what project for physics can i make from your circuits? by the way im an electronics hobbyist (= thanks in advanced for the answer. cheeers!!!! I like & love this website. Eshkariel

      Delete
  28. Dear Swagatam,
    I have built your "auto shut off charger",Its working fine with 12 volt 3 amp Transformer,
    Can you suggest me some way so that I can adjust the current output(Amp) from the trans former,Then I can adjust it for no of batteries in my battery bank, & even i will be able to charge a single battery,Should i try with LM 338,

    ReplyDelete
    Replies
    1. Hi Avisek,

      Just study the following circuit and see how the resistors need to be calculated for adjusting the current to the battery.

      http://homemadecircuitsandschematics.blogspot.in/2012/04/how-to-make-solar-battery-charger.html

      Delete
  29. Dear Swagatam,
    Can you suggest me a CFL driver for 12 v circuit,in which efficiency will be very good,means less loss(heat loss and other loss) with the capacity of 20 Watt approx,
    I have purchased one CFL circuit from market,which have a very small transformer inside.

    I have combined two circuits of you for charger,1 with LM317 for controlling voltage,another with IC 741 to control relay to cut the line from battery,In between if the battery volt gets down then the relay energies and start the charging process again.
    Thanks for your circuits,

    which transformer should i use to charge two 7ah 12 battery,15 v 1Ampor 15 volt 1.5 Amp,
    According to specification each battery needs 1/10 of Ah means 700 m Amp,So for 2 it will be 1400 around 1.5 Amp,But as the charging process can restart automatically i think 1 amp will increase battery life,I am in dilemma ,Please guide.

    Many many thanks for your help

    ReplyDelete
    Replies
    1. Thanks Avisek,

      I think a 1.5 or even 2amp transformer will be good. 1/10th rating is right but sometimes a little higher current becomes necessary for proper charging process, so you may use a 1.5 or a 2amp transformer.

      Regards

      Delete
    2. D-TECH is this inverter a sinewave or a sqaure wave...

      Delete
    3. It's a square-wave inverter circuit

      Delete
    4. @avisek

      where you have purchased clf inverter and what is the cost of it?

      Delete
  30. hai swagatam
    i have designed ur 50watt home made inverter in bread board for testing
    but not getting the desired output,i used 12-0-12v 500ma transformer,12v 7.2ah battery
    all the connections are right
    so please tell me the solution

    ReplyDelete
    Replies
    1. Hi Phani,

      The transformer should rated at least at 5 amps, 500 mA will not do.

      Delete
  31. Your circuit is nice,but I have another design of an inverter that may power a number of appliances,I designed it in the year 2005 July.It only requires few components: a Transformer,1 capacitor,2 transistors and 2 resistors thats all.I can post upon request. (e-mail:clubaini@yahoo.com)

    ReplyDelete
    Replies
    1. You can send it to me along with some content of around 300 words, I'll publish it here with your name.

      Thanks

      Delete
  32. great work swagatam ...shareing your knowldge with others ...nice work swagatam(means welcome in telugu)......
    sandy

    ReplyDelete
    Replies
    1. Thank you very much Sandy!

      In Hindi also it means the same:-)

      Delete
    2. sir
      again in malayalam language of kerala u r most welcome..... SWAGATAM

      Delete
    3. thanks Rohith, you are welcome too!

      Delete
  33. can you say me the precutions should be taken in this circut

    ReplyDelete
    Replies
    1. You should be well versed with all the basics of electronics before starting this project.

      Delete
  34. can we use single 12 volt 7AH battery?

    ReplyDelete
  35. hi swagatham

    do you have deep discharge controller circut for 12v 4.5AH battery?

    ReplyDelete
    Replies
    1. Hi Sandy
      can you please elaborate a little more....

      Delete
    2. deep discharge will leads battery to dead completely....that mean when the battery discharges its complete power it will dead..so inorder to avoid this deep discharge controller is used it will gives buzzer and shutdown the device when the voltage level drops below 10.5[deep discharge occurs.
      By
      sandy

      Delete
  36. hie..

    i have got that deep discharge controller circut which include yours low voltage cut oof circut..

    my question is

    1)can i use this op of 230v to feed 40w floursent bulb?
    2)how to connect low voltage cutoff circut with this circut ?
    3)can i use automatic battery charger useing LM388 to give ip to this circut?
    4)i want manifacture this project and do marketing what will be the cost for these 3 circuts?
    thanku for your wonderfull circuts

    ReplyDelete
  37. Thanks Sandy, I'll be publishing an outstanding battery charger circuit by tomorrow, please wait until then, the circuit will incorporate all the necessary features.

    Regards.

    ReplyDelete
  38. ok thanku ...what abot the remaining two circuts is it ok ?

    ReplyDelete
  39. hai swagatam sir
    i am manoj.and i want a help that is i want to make a quadcopter and i want the help of yours

    ReplyDelete
    Replies
    1. I am sorry Manoj, it is a highly complicated mechanical device, I have no idea regarding its construction details.

      Delete
  40. 50w inverter and low voltage cut off circuts

    ReplyDelete
  41. hi swagatham
    will it take more time to publish circut?

    ReplyDelete
    Replies
    1. Hi Sandy,

      Please check out the following link:

      http://homemadecircuitsandschematics.blogspot.in/2012/07/making-simple-smart-automatic-battery.html

      Regards.

      Delete
  42. can i use two 2.5A tramsformer in series to get a 5A transformer? thanks.....waiting for you reply. D-TECH

    ReplyDelete
    Replies
    1. No, you will have to use a single 5amp rated transformer

      Delete
  43. thanku can i use that charger circut with this circut

    ReplyDelete
  44. the circut which you posted yesterday night

    ReplyDelete
  45. hi sawgatham

    check this linkhttp://www.electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?sno=112

    their is a automatic battery backup circuit

    and say can i include deep discharge control circuit along with battery backup circuit

    ReplyDelete
    Replies
    1. Hi Sandy,

      Please tell which deep discharge circuit you want integrate with the above link's circuit?

      Delete
  46. hi swagatham

    when 12v circuit was droped to 10v then buzzer should be produced thats the circut i want...

    ReplyDelete
    Replies
    1. Hi Sandy,

      Yes you may integrate the two circuits together, no problem.

      Delete
  47. Sir what could be the max DC input we can give to this circuit and what will be the max power output??? -jerry

    ReplyDelete
    Replies
    1. Not more than 24 volts with the shown components, the power should get doubled then.

      Delete
  48. sir how about using solar cells to charge the input batteries?

    ReplyDelete
    Replies
    1. Hi Jerry,

      Yes you can use a solar panel with a regulator for charging the batteries.

      Delete
  49. dear swagatham
    I complete the 100w inverter circuit designed by you. I use 12-0-12. 3AMP transformer and 6v scooty battery. but the transister (540)getting tooo hot and there was no output. What can I do?
    CHANDRASEKAR - MADURAI- TN

    ReplyDelete
    Replies
    1. Dear Chandrashekar,

      It should have worked...anyway if you are having problems with the circuit, I will suggest, you just add two more transistors to the circuit and you will get 100% results, please do it as shown in the below given link:

      http://homemadecircuitsandschematics.blogspot.in/2012/07/simplest-and-best-100-watt-inverter.html

      Regards.

      Delete
  50. Dear Swagatam,

    I tried your circuit on a bread board with all the right parts, but used a 12v 7ah battery. The results were not fruitful as there was no light at the output and moreover it was disastrous. There was a blast and i heard a firecracker sound from TIP127(T3 in your diagram). I don't know why because both TIP127(T3 and T4) were mounted with large heat-sinks. Please help me out. Can the circuit be modified so that 12v 7ah battery can be used. And i also want to know whether a CFL bulb can be used.

    ReplyDelete
    Replies
    1. Dear Toni,

      The transistors should be mounted on separate heatsink, if you mount them over a common heatsink, they will surely blast.

      You may modify the above circuit into the following one, which will work 100%:


      http://homemadecircuitsandschematics.blogspot.in/2012/07/simplest-and-best-100-watt-inverter.html

      Regards.

      Delete
  51. hi sir,
    can you please explain the function of d1 and d2. and why are the necessary?.

    ReplyDelete
    Replies
    1. D1 and D2 are placed for protecting the transistors from reverse back emf generated by the transformer winding during transistor switch OFFs...

      Delete
  52. sir
    i want to make this inverter but all required parts are not available here. so, can i buy parts online if yes then how and how much money will expend please tell me soon.
    my email id-sujeetsingh.kumarsingh@gmail.com
    cont no.- +918092582566

    ReplyDelete
  53. sir
    please tell me can i buy all parts online if yes then how and how much money will expend,
    sujeetsingh.kumarsingh@gmail.com

    ReplyDelete
    Replies
    1. Hi Sujeet,

      Buying parts online can be very costly, so i'll suggest you to buy them from the local market.

      Please build the circuit shown in the following link, because I have tested it, the circuit given in the above article is not a tested one:

      http://homemadecircuitsandschematics.blogspot.in/2012/07/simplest-and-best-100-watt-inverter.html

      Delete
  54. Hai,

    i have 40w inverter circuit which is not able to light up above 11w CFL, like 14 or 18watt CFL's, circuit is using 1351 TRansistors, can u tell me the reasons or components which might be the problem

    ReplyDelete
  55. hi sir ..............
    i want to conect resistor,capacitor,transistor. etc.....i mean i want connect the ckt through a wire ,,,,,i mean with out pcb............is it possible plzz tell me sir...........as early as possible

    ReplyDelete
  56. i bwant to make 50 watt inverter plz tell me sir i want to connect the parts through only a wire with out pcb ,,,,,,,,,,,,,,,,,,is it possible ,.......plz reply me as soon aspossible

    ReplyDelete
    Replies
    1. No it won't be possible for this design.
      Type "simplest inverter" in the search box, you will get the required article with another design which you can make without using PCB....

      Delete
  57. Hello sir,
    Whats the difference between T1 and T2, and if I get the parts:how do I know which of the pins is emitter, collector and base as in transistor.

    ReplyDelete
  58. You will have to check the datasheet online for getting the exact information regarding each parts pin designations

    ReplyDelete
  59. Hi Sir ,
    can u please tell me the exact steps for making the solar inverter of 50W which i will use it for 12v, 135amp battery and a solar panel. Please draw the circuit diagram for the same also please tell me components required for making the inverter. Please reply on 154rajeev@gmail.com

    ReplyDelete
    Replies
    1. Hi Rajeev,

      I'll try to do it within a couple of days and post it here as a new article.

      Delete
  60. WHAT IS 8050 IN CIRUIT?IT IS TRANSISITOR.BUT WHAT IS ITS FULL NAME?

    ReplyDelete
  61. Sir, I am confident that i made the circuit perfectly//only thing i used differently is the battery. I used 12V, 1.3Ah battery. So, i connected a 75w bulb at output and Iam not getting the glow. Do you think this is because of the battery?? PLzz reply ASAP!!

    ReplyDelete
  62. Sit, Iam doing this aas my project and my deadline is november 3rd. Please tell me is it's OK to use 12V, 1.3AH battery instead of 12V,10Ah batter??

    ReplyDelete
    Replies
    1. Yes it's because of the battery, it should be at least 10AH rated, and the transformer should be preferably 9-0-9v/5amp.

      The output transistors must be mounted on big heatsinks.

      There's another good circuit here:

      http://homemadecircuitsandschematics.blogspot.in/2012/09/mini-50-watt-mosfet-inverter-circuit.html

      Delete
  63. Sir I have used BC247 instead of BC 316..the shopkeeper told me they are 99% eqaul!! is it true!! THnx in advance!! :D

    ReplyDelete
    Replies
    1. I tried to find the datasheet of BC247 online, but could not find it, means it's not a popular transistor and should not be used.

      BC316 is a PNP Darlington transistor, I am sure not about the one you have procured...

      Delete
  64. Sir can i use a 12v 1.5amp transformer to power two cfl lamp

    ReplyDelete
    Replies
    1. No you will need a 5 amp transformer for illuminating two CFLs

      Delete
  65. Sir , i thought if 12v 1.5Amp transformer is to be used ,the available output power would be 12v * 1.5=18watt and this should be sufficient for lighting two 5watt cfl lamp.am i correct ?

    ReplyDelete
    Replies
    1. The efficiency will never be 100%, you will get only 60% from it, but you can try, if you are lucky you may get the results.....the battery should be minimum 7.5AH rated.

      Delete
  66. What is the frequency output of above ckt? I think its 34 Hz as per your formula!

    ReplyDelete
    Replies
    1. On a frequency meter it shows around 50 Hz.

      Delete
  67. Pls sir, can you show me the formula for calculating the value of the base resistor of T3 with the figures and answer shown.

    ReplyDelete


  68. R5 = (Ub - 0.6) × Hfe ÷ T3 collector load current

    Ub = 12V

    Hfe of T3 = find it using a DMM

    T3 collector current can be found by ohms law, I = V/R = 12/R7 = 12/22 = 0.54Amps

    If we take the Hfe of BC316 as 60, then we get

    R5 = (12 - 0.6)x60/0.54 = 1K2, any lower value will also do for increasing current and power of the inverter.

    ReplyDelete
  69. HI, I HAVE A SMALL 12V 50 W UPS INVERTER, WHICH I USE TO LIGHT 11W 3 CFL LIGHTS, IT IS AC CURRENT, CAN I GET SMALL FAN TO CONNECT IT, I SEARCHED IN MARKET I DIDNT GOT, SMALL 12V DC FAN IS AVAILABLE, BUT I AM NT GETTING IN AC, PLEASE HELP...

    ReplyDelete
    Replies
    1. Hi,

      I am not sure where it may be available, you may try searching online with different keywords, you should be able to find it, or may be your local electrical appliance dealer will know better.

      here's one example:

      http://shop.rabtron.co.za/catalog/120x120x38-220vac-dp200a-p-2701.html

      Delete
  70. hi swagatam
    can u give me a circuit for inverter without transformer ?????

    ReplyDelete
    Replies
    1. Hi Dilip,

      For eliminating transformer in an inverter, the input DC supply will need to be equal to the required output AC supply.....

      Delete
  71. Can you tell which transistor I can use in this cicuit instead of BC316 ?

    ReplyDelete
    Replies
    1. BC316 is a Darlington type of transistor, and there's no replacement for it in that range.

      You may try 8550, but i am not sure whether it will give the same results or not....

      Delete
  72. can i make this circuit using ic 555 ??

    ReplyDelete
    Replies
    1. Yes, if you know how to use it with the circuit.

      Delete
  73. In this ckt you have used R-C phase shift oscillator & 4 that the formula for freq is
    f=1/(2* 3.14* RC* sqrt 6)

    ReplyDelete
    Replies
    1. So by this formula oscillation freq is 2.95 Hz as per given component value.
      You are please requested to explain ur formula for freq: f=1/1.38RC

      Delete
    2. The frequency may be calculated using the formula:

      f = 1/1.38*R*C (C is in Fards, R is Ohms)

      As per the values in the diagram the frequency would be 33Hz, so I think the resistor values R1/R2 should be made to 68K for getting exact 50Hz frequcncy...

      Delete
  74. hi swagatam,
    im plannning to use car battery with a capacity of 70amperehour connected to an inverter 500w to light up 4 220v/15watts cfl, how long my battery last?

    thanks,
    shodi

    ReplyDelete
    Replies
    1. Hi Shodi,

      If the battery is fully charged it might provide back up for 8 to 9 hours.

      Delete
    2. thanks swagatam,

      what if i used a 12v/4pcs. 8-15watts cfl bulb, connected to a car battery directly..how long would my battery last, do i still need a safety breaker or not? how about a led cfl bulb, what's the difference in power consume?

      note: my car battery just newly bought..

      Delete
    3. cfl bulbs will not operate directly because they are made for 220V ac operation.

      LED cfl are also intended for mains operation, they won't operate on battery directly, it will need to be opened and modified for 12v operation.

      power consumption will be almost the same.

      Delete
    4. safety breaker will be required for all applications to avoid over discharging of the battery.

      Delete
  75. do i still need to use a knife switch or a safety breaker?
    can a car battery still lights a cfl bulb in a few meters of wiring it, does it still have the same brightness regardless of the distance of electrical wire from source to bulb?

    ReplyDelete
    Replies
    1. wire length will not affect the current or brightness of the cfls.

      Delete
  76. Replies
    1. yes but it will not support more than 20 watts.

      Delete
  77. Can I use AMW (R1 R2 R3 R4 C1 C2) directly to T5/T6 (2N3055) for simplicity? Because in this diagram T1/T2 with AMW forms frequency generator, and T3/T4 forms Amplifire. So if I want to avoid this complexity and use R1---4, C1 C2 with wirewound/PPC as AMW directly connected to Power transistor 2N3055 do it work?

    ReplyDelete
    Replies
    1. No that will not work, 2N3055 will require relatively higher current for driving the transformer which cannot be received directly from the AMV

      Delete
    2. So if I directly connect N-channel MOSFET with AMV in place of 2N3055 (as per my idea) for avoid above complexity will it work?

      Because transistor are current operated but MOSFETs are voltage operated.

      Delete
    3. Theoretically it looks it might work, but practically the results can be weird.

      You may try it, though... cannot be confirmed without a practical test.

      Delete
  78. Hi Sir, I there any circuit for around 100w inventor which can be used for laptop. I read in your othe 1000w inverter that its square wave and can't be used for computer. this is easy but http://homemadecircuitsandschematics.blogspot.in/2012/07/simplest-and-best-100-watt-inverter.html looks quit difficult to me

    ReplyDelete
    Replies
    1. Hi Ram

      I'll be posting one simple circuit diagram of a modified sine wave inverter within a few days using the IC 3525, please wait until it gets published, the circuit will be easy for you to build and configure.

      Regards.

      Delete
  79. is there any alternative for 5amps transformer

    ReplyDelete
  80. sir....iam ahmed...i want to make a circuit which is useful to light up the cfl bulb with 9volts battery...please give me suggestion....thanks in advance...........

    ReplyDelete
    Replies
    1. with a 9V PP3?? I doubt it, its current will be too low to light a CFL bulb. Not feasible.

      Delete
  81. 9-0-9 volt, 5 amp transformer not available in market. so what can i use 12-0-12 volt, 5 amp transformer.

    ReplyDelete
  82. bc 316 not available in market. please tell me sir equivalent transistor of bc 316.

    ReplyDelete
    Replies
    1. There's no alternative to BC316....you can try this circuit instead:

      http://homemadecircuitsandschematics.blogspot.in/2012/09/mini-50-watt-mosfet-inverter-circuit.html

      Delete
  83. Sir
    I going to made solar tracking system in my project. Please sir can you give me simple solar tracking circuit. Which i can easy made

    ReplyDelete
    Replies
    1. Solar trackers require many mechanical operations controlled with a smart electronic circuit, so there cannot be an easy circuit for it.

      you may refer to the following circuit:

      http://homemadecircuitsandschematics.blogspot.in/2011/12/how-to-build-dual-solar-tracker-system.html

      Delete
  84. thank you so much for your helpful assistance....

    ReplyDelete
  85. Hai,
    I need circuit for to light up 14 cfl wih >.85PF so what i need to change in circuit

    ReplyDelete
    Replies
    1. use a 10 amp transformer and 24V 20ah battery.

      Delete
  86. hi getting BC316 is not possible can you tell me any transistor equivalent to it.

    ReplyDelete
    Replies
    1. Hi, try this circuit instead:

      http://homemadecircuitsandschematics.blogspot.in/2012/07/simplest-and-best-100-watt-inverter.html

      Delete
  87. Dear Sir....
    I need to submitted my project on 3 phase inverter. plz recommended for the same and if there is any related circuit diagram provide it to me as soon as possible.

    ReplyDelete
    Replies
    1. Dear Unknown,

      there's one diagram given in the below link, but it's without explanation, I'll surely include an article regarding this soon in my blog too:

      http://www.gophoto.it/view.php?i=http://www.chinaicmart.com/uploadfile/ic-circuit/2009720211839912.gif#.UUm24BeXTTo

      Delete
    2. thanxs alot sir for ur kind support....

      Delete
  88. sir ..
    i have 12-0-12 transformer only
    this circuit required 9-0-9 transformer what can i do

    ReplyDelete
    Replies
    1. you can use it, but the voltage will be slightly lower at the output.

      Delete
  89. Hi Sir,

    can u tell me whether I can use a 12v 7Ah battery in this circuit or not? if yes then what would be the backup time?? secondly, how to recharge the battery used in this circuit and how much the circuit costs??

    thanks
    Partha

    ReplyDelete
    Replies
    1. Hi Partha,

      yes you can use 12V 7ah for this inverter, back up time will depend on the load wattage.

      you will have to recharge it externally using a 14V 1 amp ac/dc adapter

      Delete
    2. thanx a ton sir, now would you like to tell me how much the circuit costs approximately if I want to make it on my own?

      regards,
      Partha

      Delete
    3. Hi Partha,

      I am sorry I am not sure about the present part rates used in the project.

      Delete
  90. I am in the need of very low cost about(<1000 INR)voltage stabilizer ciruit which should works with my domestic AC voltage 90 V.If any inverter which can works with this AC volage(i,e 90 V) can suggest me . with advance thanks,
    AK,Assam India

    ReplyDelete
    Replies
    1. You can try the following stabilizer circuit, it's cheap and effective:

      http://homemadecircuitsandschematics.blogspot.in/2011/12/how-to-build-2-stage-mains-power.html

      Delete
  91. i m not getting transsistor of bc 316 which one i can use at its place please reply fast.

    ReplyDelete
  92. Swagatam sir,
    I am Preston Jose. I am an everyday visitor of your blog. I like most of your circuits. I made your 50watt inverter, 100va simple inverter and the led driver. The thing is I started studying electronics from your blog. All of your circuitsworked pretty well and no problems till . I have a request . Can you post a UPS or Inverter circuit with the following principles;
    500 watt output
    800 va load capacity
    built in charger
    external battery mounting
    indicators for-mains on,ups on,battery low,overload,battery ready(full)
    Buzzer alaram for battery low and oveload
    Sine wave

    If you get time, please do it.
    My email id is preston.daffodil@gmail.com

    ReplyDelete
    Replies
    1. Hi Preston, thanks!
      As you may be seeing I have already posted many inverter designs, many battery charger circuits and relay change over circuits, all these are in fact the stages of an UPS, so you can simply make all these stages separately as explained in the relevant articles and at the end integrate them together for getting the final design.

      Begin with the inverter circuit, then conclude with the charger and the change over stages. You can keep in touch with me as you move ahead with the projects.

      Delete
  93. Swagatam Sir,
    Can you briefly describe the working of this invrter.
    i need it to explain in the science exhibiton.
    You can explain it here or you can send to my emali address
    preston.daffodil@gamil.com

    ReplyDelete
    Replies
    1. Preston, it has been already explained in the above article, you can make it short as per your convenience.

      Delete
  94. Hi Swagatam,

    can we run the 240 v, 3 hp, singlr phase motor on 12v battery?
    what kind of circuit will it need?
    can you design it?

    ReplyDelete
    Replies
    1. Hi Chandrashekhar,

      You would require a huge inverter/battery for that....may be a 4kVA inverter and a 200ah batery. It would be better to buy it readymade than trying to make since it could be quite complex to make such a huge inverter...

      Delete

Readers are requested not to include external links while commenting. For consulting a diagram, upload it on Google Drive and provide the link here.