Saturday, November 2, 2013

Automatic Transfer Switch (ATS) Circuit

In this article we investigate an ATS circuit for initiating an automatic changeover from mains supply to generator supply through many intermediate transfer stages which involves activating the fuel valve, choke valve and the generator starter. The circuit was requested by Mr. Hari, and another dedicated reader from this blog.


Request #1


Dear Swagatam,


I'm Hari, from Indonesia. Thank you for your circuit ideas, i made a battery charger based on your design. Right now, i'm looking for Automatic Transfer Switch (ATS) for my portable generator. It's 5000VA LPG powered generator with electric starter. Buy ready to use ATS is very expensive, i want to make it myself. Can you help me design the ATS?

Right now, i need to shut off the LPG valve manually to turn off my generator. I have plan to add LPG solenoid valve so i can close/open the LPG supply electrically. And add mechanic solenoid (push-pull, normally pull) to automate the choke.

The ATS system feature i need are:

  1. detect main supply, during normal condition (when main supply on), the ATS close the main to load connection and open the generator to load connection
  2. when main supply off, the ATS open the main supply to load connection, but keep the generator to load connection open.
  3. then, the system will activate LPG solenoid valve (normally closed) to open LPG supply to the engine and activate mechanical solenoid (normally pulled) to push the choke grip to START position
  4. after that, the ATS will send signal to the generator starter and start to crank the generator automatically maximum for 5 seconds. If the engine fails to start within 5 seconds, the system will stop for at least 5 second before attempting to start the engine again.
  5. When 3rd trial fails, the system activate an alarm (it could be flashing light or sound).
  6. if the starter succeeds, and the generator runs, the system will wait for 10 seconds then the system will
  7.  deactivate mechanical solenoid so that it pulls  the choke grip back to CLOSE position.
  8. after this, finally the system will close the connection between generator to load.
  9. if the main power back, the ATS will open the generator to load connection, and keep the generator run without load for 2 minutes and turn the generator off by deactivate LPG solenoid valve.
  10. several seconds later, the system will open the generator to load connection, it close the connection between main to load connection

Request#2

Sir in my area, we have problem of load-shading. i want a circuit (system) to automatically turn ON a self start gas generator (6 KVAR) when Light (WAPDA Supply) goes OFF and load should shift to generator by itself.
And when Light (WAPDA Supply) is back, automatically turns OFF generator and load should be connected to WAPDA Supply..

I know a system using automatic change over and a relay. it is only to automatically turn off generator and shift to wapda..
automatic change over is used to shift from generator to wapda and relay is used only to turn off generator..

Sir, plz tell me a system so that we can make our task easy to turn on and turn off generator..
i think there may be a system such that when light goes off load automatically connects to generator, and we use remote or cell phone to turn on generator..
and to turn off there is already an automatic system...



Circuit Description


The ATS circuit or automatic relay changeover for generator/ mains circuit as shown below can be understood as follows:


For so long as home mains is present T1 base receives the rectified low voltage DC and keeps T2 base grounded.


With T2 base grounded REL1 is held switched OFF along with REL2, REL3 and REL4, the whole circuit thus stays switched OFF.


With REL4 deactivated, the DPDT holds the home mains supply with the load and the load gets powered via its N/C contacts.


Now in a situation when home mains fails, T1 is inhibited from its base drive and it instantly stops conducting.


With T1 OFF, T2 now activates, switching ON REL1, which in turn activates the LPG solenoid valve for allowing the fuel to reach generator combustion chamber.


After a few seconds delay T3/REL2 also activate pushing ON the choke solenoid into start position. The delay may be fixed by the tweaking the values of R7, C3.


REL2 activation switches ON the 555 astable which starts counting upto 5 seconds and triggers T4/REL3 so that the generator starter motor begins cranking the gen.


The astable allows this to happen for 5 seconds, if the generator starts, a 12V supply from a 12V adapter connected at the output of the generator feeds T6 base and disables the 555 astable.


The above 12V from the gen also activates the 4060 timer/latch which counts for about 10 seconds after which its pin#3 goes high.


The pin#3 high pulse latches the IC and also feeds T5 which deactivates REL2 so that the choke solenoid is pulled back to "close" position.


The 4060 output also simultaneously activates T7/REL4 making sure that the load now gets connected to the generator AC via N/O contacts of REL4.


Now suppose due to some fault, the cranking of the generator starter fails to initiate the generator, the astable makes three attempts with 5 seconds interval between each try.


Since the above pulses also reach IC4017 counter, after three pulses the IC4017 output sequence reaches its pin#10 which instantly latches itself due to a high at pin#13, and also disables the 555 astable by grounding its reset pin#4 via T6.


REL3 now stops feeding the crank mechanism.


An additional transistor driver/RELAY may be configured with pin#10 of IC 4017. The N/O contacts of this relay then could be wired with an alarm for the required warning in case the cranking attempts fails to start the generator.


When mains AC returns, T1 receievs the atached 12VDC at its base, however due to the presence of R2, D3, C5, T1 is restricted from the base voltage for a few seconds, until C5 charges.


In the meantime T7 is disabled and REL4 reverted to home mains position by T8, this happens as soon as mains returns, so that the generator gets immediately unloaded from the connected appliances.






Parts list for the above automatic transfer switch or ATS circuit


R1, R4, R5, R6, R7, R8, R9, R10, R11 = 10K

R2, R3 = 100K
C4 = 0.1uF
C1----C5 = timing capacitors, can be between 10uF to 100uF
All transistors are BC547
All rectifier diodes are = 1N4007
All zener diodes (D6, D10, D12) are = 3V, 1/2 watt

REL1---REL3 = 12V/10 amps/400 ohms
REL4 = 12V/40amps or as per load specs


 IC 555 Astable Configuration


IC 4060 Timer Configuration






21 comments:

  1. Hi Swagatam sir,
    wish u &ur family a Happy Diwali...may god bless u...

    ReplyDelete
    Replies
    1. Hi Sanatan,

      Wish you too a Very Happy Diwali!!

      Delete
  2. if i use 3v input on ic LM338 or LM138, can it produce 5.88v output, assuming R1 and R2 are 270R and 1000R?

    ReplyDelete
  3. Hi Swagatam,
    Thank for your effort to help us. I'll try to make it.
    Warm regards,

    Hari

    ReplyDelete
  4. Hello sir,
    Wish u and ur family a very very happy dipawali .

    ReplyDelete
    Replies
    1. Hello Avijeet

      Wish you too and your family a Very Happy Diwali.

      Delete
  5. Hello sir,
    Actually I want to make remote switch using ht12e, ht12d,rf 434mhz tx and rx but this all are not available in my local market.if u suggest me some sites who sells good quality products and reliable in products delevery .this will help me a lot.
    Thanks

    ReplyDelete
    Replies
    1. you can try this site:

      http://www.sunrom.com/search?q=remote+contro&yt0.x=-771&yt0.y=-136&yt0=submit

      Delete
  6. Please sir, if i power the LM338 with a 6v, 4AH rechargeable battery and regulate its output voltage to 4.7v, and use it to charge 5 mobile phones at once, how many times can i use it to charge the 5 phones before recharging the 6v battery again?

    ReplyDelete
    Replies
    1. 6V4AH will support at the most two mobile phones, and will need recharging after a single charge of the two mobile phones.

      Delete
  7. please tell me about ic 4060 there is only two pin use pin 3,16circuit ic 555 circuit there is no nagative line is connected and and ic 4017 i do not understand plz email me

    ReplyDelete
    Replies
    1. set the rest of the pins as shown here:

      http://img.bhs4.com/ca/6/ca6021e3fd1d873281438d1bf721ef4e27ceaa0b_large.jpg

      use R1 = 1meg
      R2/R3 = set for 10 seconds
      C1 = 0,22uF

      555 and 4017 remaining pins are configured as per their standard connections, check their datasheets.

      Delete
  8. Sir,
    Can you please provide me the schematic for 555 and 4017 connection or datasheet.
    I am much interested in that circuit.I will make that one and provide you the feed back.

    ReplyDelete
  9. Pls can you update the circuit about 4017 & 555 ,Thanks.

    ReplyDelete
  10. pls sir can the circuit be use with a remote

    ReplyDelete
  11. pls help me sir am in need of it

    ReplyDelete

Readers are requested not to include external links while commenting. For consulting a diagram, upload it on Google Drive and provide the link here.

Readers are advised to proceed with the construction of the presented circuits only after understanding the concepts from the core. Not adhering to this can lead to failures and frustrations.