Sinewave Inverter


300 Watts PWM Controlled, Pure Sine Wave Inverter Circuit

In this article we learn regarding a 300 watt power inverter circuit which uses a PWM concept for acquiring an output waveform that's equivalent to a sine wave. The concept exploits the versatile features of the IC 555 where a couple of them are used for generating the intended results.

Make this IC 556 Pure Sine Wave Inverter circuit

This 556 IC based sine wave inverter is quite identical to the previous design and employs a single 556 IC instead of two 555 ICs for getting the desired pure sine wave output.

Modified Sine Wave Inverter Circuit Using IC 3525

We all know pretty well about this chip the IC 3524/3524 which is basically a PWM generator IC, which is fundamentally used for making PWM controlled inverer circuits

More Inverter circuits:

Make 400 watt MOSFET Sine Wave Inverter Circuit |Homemade ...

Simplest Full Bridge (H-Bridge), Modified Sine Wave Inverter Circuit ...

Make This 1KVA (1000 watts) Pure Sine Wave Inverter Circuit ...

How to Build a Homemade Pure Sine Wave Inverter, Using IC 555 ...

Making a Sine Wave Inverter from an Audio Power Amplifier ...

Digital Modified Sine Wave Inverter Circuit - 250 watts |Homemade ...

How to Build a100 Watt, Pure Sine Wave Inverter Circuit ...

Making a Pure Sine Wave Inverter - Concept Explored |Homemade ...

How to Make a 150 Watt Modified Sine Wave Inverter Circuit Using ...

How to Make a Simple 200 Watt Modified Sine Wave Inverter Circuit ...

Modified Sine Wave Inverter Circuit Using two IC 4017 |Homemade ...

How to Design a H-Bridge Circuit for Modified Sine Wave Inverters ...

How to Build a Simplest Modified Sine Wave Power Inverter Circuit ...

How to Make a 500 VA PWM Controlled Modified Sine Wave ...

How to Design an Inverter - Basic Circuit Tutorial |Homemade Circuit ...

How to Convert 12V DC to 220V AC Using IC555 Boost Circuit ...

How an Inverter Functions, How to Repair Inverters - General Tips ...

How to Make a Mini Homemade Uninterruptible Power Supply (UPS ...

How to Use IC 555 for Generating PWM Outputs |Homemade Circuit ...

How to Make a Simplest Triac Dimmer Switch Circuit |Homemade ...

How to Design Your Own Inverter Transformer |Homemade Circuit ...

Mini 50 Watt MOSFET Inverter Circuit |Homemade Circuit Designs ...

How to Make a Simplest 200 VA Uninterrupted Power Supply (UPS ...

Simplest and Best 100 Watt Inverter Circuit for the Newcomers ...

Load Independent/Output Corrected Inverter Circuit Discussed ...

How to Make a 200 Watt Transformerless Inverter Circuit ...

Improved IC4017 Inverter Circuit Discussed |Homemade Circuit ...

How to Make a Simplest 150 watt MOSFET Inverter Circuit ...

Modify a Square Wave Inverter to Sine Wave Inverter Circuit

1 kva full bridge modified sine wave inverter circuit

51 comments:

  1. hi m janvi
    How To Make a Cell Phone Jammer?

    ReplyDelete
    Replies
    1. I will try to cover this topic soon in my blog.

      Delete
  2. sir how to increase the load regulation in modified sinewave inverter (ic 4017 is used ) ..? actually i am getting 0.90a , 250v output but when i put a 100w load voltage will be reduced seviourly but load works fine , but the problem is i cant connect another 60w load simeltaneously??

    ReplyDelete
    Replies
    1. please show me the circuit diagram which you have employed...i'll try to figure it out.

      Delete
    2. i have maild you the driver section of my inverter sir.. because rest of the circuits are same as your design using ic 555 and 1c 4017 (modified sine)..

      Delete
  3. sir , what is the maximum current dat can be taken by irf 540 mosfet at vds = 24v ?? according to its datasheet it is 5 amps , is it true??

    ReplyDelete
    Replies
    1. Upto 30 amps...you can refer to the datasheet here:

      http://homemadecircuitsandschematics.blogspot.in/2013/01/irf540n-mosfet-specifications-datasheet.html

      Delete
  4. hi Mr. Swagatam im new here i want to know how to bile a 3000 watt inverter simple because i don't know enough about electronic but im very exciting about it & i want to know how to build a 3000 watt transformer (enough small but powerful) please help me.

    ReplyDelete
    Replies
    1. Hi Rashel,
      you should begin with smaller designs then upgrade them into higher wattage types, I have discussed many inverter designs in this blog, you can select any one from them and start your learning course.

      Delete
  5. Hi Swagatam

    Here is a schematic of a simple sine-wave oscillator, which oscillates between 0-10v at 50Hz. I was just wondering if we can use a step-up transformer to get 220v?

    ReplyDelete
  6. Sorry, I forgot to attach the schematic. Here it is:

    https://dl.dropboxusercontent.com/u/20969135/Sine-wave%20oscillator.gif

    ReplyDelete
    Replies
    1. Hi Abu-Hafss,

      The circuit will not handle higher amps and will require an output stage for amplifying amps to the transformer. Moreover this circuit won't generate both the AC half cycles, which makes it ineffective as an inverter.

      Delete
  7. sir my task was ups as final year project.. but i have made an inverter yet with h bridge of irf3205 its output is a rectangular wave with +12,-12 V 24peaktopeak ... now plz guide me what should i do next for making it modified sine wave and stepping up and filtering :(( plz i need urgent help

    ReplyDelete
    Replies
    1. Show me the circuit diagram, only then I would be able to say anything.

      upload it to any image sharing site and give me the link.

      Delete
    2. Ok i m messaging u on ur fb profile ... plzzz plzzz help me ssooon

      Delete
  8. Hi Swagatam,I want to know that, in my home there is a pure sine wave inverter with a battery.I know how to convert 12 v DC to 230 v AC but I don't know the reverse or charging process that means 230 v AC to charge the 12 v battery.can you tell me the same MOSFET H-bridge used for charging or separate charger used when battery is drained at rated charging point.can you send me the details about it.
    email- biswajitdas49@gmail.com

    ReplyDelete
    Replies
    1. Hi Biswajit, you can charger the battery with a separate battery charger circuit through an external voltage source such as from your home AC mains or a solar panel.

      I have published many cool battery charger circuits in this blog, you can select any one from this list:

      http://homemadecircuitsandschematics.blogspot.in/p/battery-chargers.html

      Delete
    2. HI Swagatam,THANKS for your reply.I know your every circuit is awesome in this field.
      I want to know, is there any "possibilities or the process" to use the same mosfet which is used in H-bridge to make dc to ac can be used for battery charging(ac to dc) process in the same circuit board using microcontroller?

      Delete
    3. Hi Biswajit,

      I am not good with microcontrollers so cannot suggest you anything useful on this.

      Delete
  9. Hello sir,can you help me with building of LCD display for a mini fuel dispenser?

    ReplyDelete
    Replies
    1. Hello Segun, Please provide an elaborate description of your requirement.

      Delete
  10. sir , max Ids of a mosfet decreases as the Vds increases ?? as per some graphs in mosfet datasheet .. ? also practically mosfet burnt as current increased a value shown in datasheet .. ? (irf 540 , max ids = around 5A at vds=24v ) ?

    ReplyDelete
    Replies
    1. Hi Vishwas, that's impossible, there might be something incorrect in your circuit. You can test the mosfet separately using a, say 20 amp 50V lamp or any other value below the specified rating, the mosfet will not burn..

      Delete
  11. oh ok.. so we can use 8 amp 500v mosfet in a 340v h bridge ciruit with a load of 2 amp safely??

    ReplyDelete
  12. ok thank u.. sir i have mailed u some graphs fom mosfet datasheet can you analyse it and tell me what they mean ?

    ReplyDelete
    Replies
    1. The left graph shows the safe operating area of the mosfet. The y-axis shows the max current that should not exceed over the dotted line on the top. The x-axis shows the max voltage that should not exceed beyond the thick dotted line at the right side of the graph, while the Vds voltage which lies on the right hand side of the thick dotted line can be applied only as a short pulse whose duration is indicated along the vertical thick dotted line.


      The right hand side graph simply shows the current/voltage response of the mosfet across its drain/source when Vgs or gate voltage = 10V

      Delete
  13. ok.. now now i have some quetions , irf 840 mosfet is rated as 8amps , 500v , but when we observe the graph,,, at vds=500v , max allowable DC current is about 0.3 amps(FROM THE GRAPH) , so can i say that 8 amps can be passed in pulse but not continuesly , continuos current of only 0.3 amps can be passed??

    thank you for your time,

    ReplyDelete
    Replies
    1. No, may be you are reading the graph wrongly, it doesn't show anything like that,
      the thick vertical line at the right shows the voltage limit after which it could applied only as pulsed voltage as given beside the line.
      The left slope indicates the current response with respect to voltage, whereas the upper white space indicates the danger zone or the restricted area for the current.

      Delete
    2. ...8 amps can be passed continuously albeit with heasink on the moset

      Delete
  14. can we use am radio ferrite core for high frequency inverter purpose? arround 250 W?

    ReplyDelete
    Replies
    1. it won't produce efficient results, because the core should be a looped type as in E-cores or in torroidal cores for getting efficient outputs....

      Delete
  15. Hi Mr. Swagatam,

    i have a defective 2kva ups, i want to salvage the transformer (48v no center tap 110v ouput), please make me a design using this transformer, and i have also mosfet ifr3205, incorporate this if possible...

    thank a lot.

    Ariel.

    ReplyDelete
    Replies
    1. Hi Mr. Ariel,

      You can try the following design:

      http://homemadecircuitsandschematics.blogspot.in/2014/01/simplest-full-bridge-inverter-circuit.html

      Delete
    2. Hi Mr. Swagatam,

      Thank you and i appreciate your design, but IC IRS2453(1)D can't found in electronic shop.

      Can you please make an alternative circuit using NE555 and 4017, or 4060 for oscillator driver..
      option 1 using 4 n-channel mosfet, option 2 using 2 n-channel and 2 p-channel mosfet..

      Thank you for your immediate response.

      Thanks a lot

      Ariel

      Delete
    3. Hi Mr. Ariel,

      The circuit that I have referred is a professionally designed circuit and will start working without any hassles, other modified designs may not be so reliable,
      if you insist, the following circuit may be tried, which has been designed by me

      http://homemadecircuitsandschematics.blogspot.in/2013/04/h-bridge-inverter-circuit-using-4-n.html

      Delete
    4. Hi Mr. Swagatam,

      Thank you for your immediate response. By the way, What type of regulator to be used to supply the VCC of IC 4049 and 4017? my Battery Voltage is 48v in series, or maybe I use one of the series battery so that i can feed 12v to IC and 48v is feed to mosfet and the ground are common. My existing mosfet is IRF3205, is suitable for this circuit?.. What is the oscillating frequency so that i can produce 60hz from the output Transformer?

      Thanks a lot Mr. Swagatam,

      Regards

      Ariel

      Delete
    5. Hi Mr. Ariel,

      You can use a 7812 IC for powering the ICs
      48V will work for the mosfets separately.
      IRf3205 is OK.
      oscillating frequency could be 600Hz at pin14 of 4017

      Delete
    6. Hi Mr. Swagatam,

      The circuit is work fine on 12v dc supply. But when i connect on 48 volts dc supply, the pnp transistors (bc557) blows out. Please help me to trace what happen.. is this exceed the Vec of BC557 because the bootstrapping network?

      Thanks a lot Mr. Swagatam,

      Regards

      Ariel

      Delete
    7. Hi Ariel,

      the 4049 IC will surely need 12V supply and not 48V....so you must apply the 4049 IC also with 12V from 7812 IC.

      48V will only go to the high side mosfet drains and must be suitably dropped before applyuing to the ICs.

      and yes 7812 cannot be used with 48V since these ICs can handle not more than 35V input.

      You can use a BC546 as an emitter follower with 12V zeer at base for getting the required 12V supply.

      Delete
    8. Hi Mr. Swagatam,

      I just want to clarify that the diode (1n4148) across the positive terminal to the output of bootstrapping network. The anode terminal is connected directly to the battery even if the supply is 48 volts?
      And also the capacitor is connected directly to the ground terminal.

      Thanks a lot Mr. Swagatam

      Regards

      Ariel

      Delete
    9. Hi Ariel,

      I have updated the discussed diagram appropriately, you may refer the same for getting a clearer view.

      Delete
  16. hi,
    I hope you watched the channel- lasersaber.
    Well, I wanted to know a bit of trade language in electronics(how we ask a components name in shop).
    I went to a shop and asked a transformer "120v-12v, 40va transformer(stepdown)". The shop keeper asked what does va means??
    I told him "Volt-ampere", then he said, he dont know.
    So can you say what exactly i should ask for the above mentioned transformer in trade language.??????

    ReplyDelete
    Replies
    1. Hi,
      If the CFL is rated at 12 watts it WILL consume 12 watts for the specified illumination, if anybody claims to produce the same illumination at a lower supply power the person may be completely faking....there are many such fake claims presented on Youtube so please don't trust them.

      Tell the shopkeeper that you want a 120V, 12V/3 amp transformer he would now surely understand

      Delete
    2. Helped me a lot,

      thanks,
      with regards.

      Delete
  17. Hi Mr. Swagatam,
    i hav 3055 tr old inverter. it can fractuate output in Changeover time..how to solve this problem...??

    ReplyDelete
    Replies
    1. Hi Sovan, I am sorry I did not understand your requirement, please explain it more clearly.

      Delete
  18. Hi sir,
    I build an inverter using ic 3524, the inverter is working fine on some appliance but won't power a small standing fan and a small clipper. Pls what can I do?
    Thanks in advance

    ReplyDelete
    Replies
    1. Hi Kolley, the fan wattage could be beyond the capacity of the inverter power that's why it's not able to move it...you may have to increase the battery AH and/or the transformer amps for upgrading the inverter range

      Delete

Readers are requested not to include external links while commenting. For consulting a diagram, upload it on Google Drive and provide the link here.

Readers are advised to proceed with the construction of the presented circuits only after understanding the concepts from the core. Not adhering to this can lead to failures and frustrations.